Comtrol RocketModem Driver Installation for Novell NetWare Bedienungsanleitung

How to Use this Document 1 RocketPort® and RocketModem™Driver Installation for Novell® NetWare®How to Use this DocumentYou can use the interactive Tab

NetWare Connect Configuration for NetWare 5.x 10 NetWare Connect Configuration for NetWare 5.xAfter the boards are initialized, follow these steps to

NetWare Connect Configuration for NetWare 5.x 11 9. To enter or change the modem type, highlight Modem Type and press Enter. The list of valid modem t

NetWare Connect Configuration for NetWare 5.x 12 21. Select Setup, which brings up the System Setup Options menu.22. Select Select Remote Access Ports

NetWare Connect Configuration for NetWare 5.x 13 33. Select Display Port Status. The Port Status window displays:If the status of all configured ports

NIAS/MPR Installation and Configuration for NetWare 4.x 14 NIAS/MPR Installation and Configuration for NetWare 4.xThis discussion assumes the followin

NIAS/MPR Installation and Configuration for NetWare 4.x 15 3. Press the Insert key to add a new board. The list of available drivers displays:4. Scrol

NIAS/MPR Installation and Configuration for NetWare 4.x 16 7. Select Ye s and press Enter. The list of AIO drivers displays:8. Scroll down the list, h

NIAS/MPR Installation and Configuration for NetWare 4.x 17 as an international board, certain harmless console messages may display.9. Press the Esc k

NIAS/MPR Installation and Configuration for NetWare 5.x 18 NIAS/MPR Installation and Configuration for NetWare 5.xThis discussion assumes the followin

NIAS/MPR Installation and Configuration for NetWare 5.x 19 The list of available drivers displays:6. Scroll down the list, highlight WHSMAIO, and pres

2Interactive Table of ContentsRocketPort and RocketModem Driver Installation for Novell NetWareHow to Use this Document 1Driver Requirements 1Locating

NIAS/MPR Installation and Configuration for NetWare 5.x 20 9. Select Ye s and press Enter. The list of AIO drivers displays:10. Scroll down the list,

NIAS/MPR Installation and Configuration for NetWare 5.x 21 installing it with the “USA” Modem country code. If the driver attempts to initialize a gen

Configuring Network Interfaces 22 Configuring Network InterfacesFollow these steps to configure each port:1. From the Internetworking Configuration me

Configuring Network Interfaces 23 4. Move the cursor to Modem/DCE Type and press Enter. The list of available PPP Modem/DCE Device Types displays:5. S

Configuring Network Interfaces 24 Configuring ProtocolsFollow these steps to configure the protocols:1. From the Internetworking Configuration menu, s

Reinitializing the System 25 Configuring BindingsFollow these steps to configure the bindings:1. From the Internetworking Configuration menu, select B

Verifying Installation 26 Adding an ISA-Bus BoardFollow these steps:1. Use the instructions in the Hardware Installation Card to install the board in

Troubleshooting 27 TroubleshootingIf you are still unable to resolve the problem, try the following:• Check to make sure that you are using the correc

RocketModem Manual Reset 28 Using RCKTTERMUse the following procedure to use RCKTTERM:1. Load the AIORCKT driver for each of the installed RocketPort/

Technical Support 29 Forced ResetThe force option should be used for specific modems that have already been allocated (acquired) by an application. Th

Installing the Driver 3 Installation and ConfigurationUse this section to install and configure the RocketPort/RocketModem driver (AIORCKT.NLM) for th

Loading the Driver 4 ISA-bus boards only (This does NOT apply to PCI boards):You can manually enter load aiorckt without any command line parameters.

NWC/Third-Party Initialization and Configuration 5 NWC/Third-Party Initialization and ConfigurationFollow these steps:1. Load the driver manually, usi

NetWare Connect Configuration for NetWare 4.x 6 NetWare Connect Configuration for NetWare 4.xAfter the boards are initialized, follow these steps to c

NetWare Connect Configuration for NetWare 4.x 7 6. To enter or change the modem type, highlight Modem Type and press Enter. The list of valid modem ty

NetWare Connect Configuration for NetWare 4.x 8 13. Choose Select NetWare Connect Ports. The list of valid NetWare Connect Ports displays:If all ports

NetWare Connect Configuration for NetWare 4.x 9 22. Select Display Port Status. The Port Status window displays:If the status of all configured ports